Lee Precision Mold 6 Cavity TL452-200-SWC
Six Cavity Commercial Quality Molds
Made for heavy duty volume production, this Lee Precision Six Cavity Bullet Mold produces .452 diameter, 200 grain, Semi Wad Cutter round nose bullets suitable for .45 ACP (Automatic Colt Pistol), .45 Colt (long), .45 Auto Rim and similar cartridges. This mold, like all Lee Precision molds, is made from aluminum and so is completely rust resistant, lighter, and heats up and cools down faster than other brands made from iron or steel. As a result, this Lee mold is easier to use, causes less operator fatigue during casting and can produce more consistent bullets than other molds made from iron or steel. Lee's 6 cavity mold blocks are machined from aluminum and assembled with steel bushings and alignment pins for lasting precision.
A sprue plate is included but Handles are sold separately. The bullet weight specified is based on using Lee's suggested alloy, your results may vary depending on the actual alloy used.
- (2) aluminum Mold Block halves (mold handles NOT included)
- Hard anodized Sprue Plate with handle
- Produces bullets that fit 45 ACP, 45 Colt (long), .45 Auto Rim and similar sized cartridges.
- Bullet diameter: .452 inches
- Bullet weight: 200 grains (with Lee's suggested alloy)
- Bullet overall length: N/A
- Distance from nose to first lube groove: N/A
- Bullet shape: Semi Wad Cutter nose
- Ballistic Coefficient: N/A
- TL for Tumble Lube
- 6 bullets are produced with each casting.
- Mold block halves are machined from aluminum.
- Assembled with steel bushings and alignment pins for lasting precision.
- Cam operated sprue plate to eliminate the pounding common to ordinary molds.
- A tangential cutoff helps reduce the nip at cutoff.
- Bullet mold will be damaged & bullet will be poor quality unless lubricated. FS Reloading recommends Frankford Arsenal Cleancast Lead Fluxing Compound or Frankford Arsenal Drop out Bullet Mold Release and Lube Aerosol.
- The Lee Precision Melter 110 V is the best method of melting your metal. Heat control is simple & your best bullets are poured with the Lee Ladle.
- Before handling lead or case lube, FS Reloading recommends Tipton Vinyl Gloves
- For Load Data information try HODGDON Powder Co.
- The following lead information is from the Lee Precision Modern Reloading 2nd Edition Book, Pages 119 & 120.
- For best results, bullet strength must be matched to breech pressure.
- Black Powder guns require Pure Lead.
- Target handgun loads should use Lead with 1% Tin. Tin makes bullet alloy more castable & harder.
- Lead with some wheel weights used for high pressure handguns.
- Use Wheel Weights for very light rifle loads.
- High Pressure Rifle loads use Linotype.
- Beware of Zinc! One part Zinc in 10,000 parts of Lead Alloy will ruin it's castability.
WARNING: Melting lead and casting lead objects will expose you and others in the area to lead which is known to cause birth defects, other reproductive harm and cancer.
USE STRONG VENTILATION
Lead contamination in the air, dust and on your skin is invisible. Keep Children and pregnant women away during use and until clean-up is complete. Risk can be reduced, BUT NOT eliminated , with strong ventilation. Washing hands immediately after use of these products before eating or smoking. Careful cleaning of surfaces and floors with disposable wipes, after lead dust has settled. Use lead-specific cleaner with EDTA or high phosphate detergent (such as dishwasher detergent). Bag wipes for disposal.
IT IS YOUR RESPONSIBILITY TO ENSURE THE SAFETY OF YOUR LOADS
FACTORS THAT WILL INCREASE PRESSURES. SOME WILL BE DANGEROUS:
- DO NOT USE more powder than recommended
- DO NOT USE a heavier bullet than recommended
- DO NOT SEAT the bullet deeper than normal
- DO NOT USE magnum primers unless using a slow burning ball powder
- Greatly oversize bullets, excessively hard bullets or cases that are too long will cause higher pressures
- High temperatures or cartridges that were stored in a hot car or trunk will produce higher pressures
Ammunition reloading can be dangerous if done improperly, and should not be attempted by persons not willing and able to read and follow the instructions included with each product exactly.
- Always wear safety glasses when reloading and shooting.
- Ammunition loaded with these tools should be used in modern guns, in good condition.
- Children should not be permitted to reload ammunition without strict parental supervision.
- Primers and gun powders, like gasoline and matches, can be dangerous if improperly handled or misused.
- We do not accept responsibility for ammunition loaded with these tools, as we have no control over the manufacture and storage of components or the loading procedure and techniques used.
Help for product 90379
We are required to provide Prop 65 product warnings by California's Dear Leader. Please give them appropriate attention.
Prop 65: Warning:
Prop 65: Warning:for the melters and bullet molds: WARNING: Melting and casting lead objects will expose you and others in the area to lead, which is known to the State of California to cause reproductive harm and cancer. For more information, go to www.P65Warnings.ca.gov. See instructions on Reducing Exposure supplied with product.
Lee Precision Mold 6 Cavity TL452-200-SWC
|Only Ships to:||United States|
|Country of Origin:||United States|
|Product Weight:||1.2 lbs|
|Calibers:||.45 ACP .45 Colt etc.|
|Bullet Type:||SemiWad Cutter, Micro Band Grove|
|Bullet Weight:||200 grain|
|Bullet Diameter:||.452 inches|
- Price in reward points: 3048