Lee Precision Mold 6 Cavity C358-158-SWC

Six Cavity Commercial Quality Molds

Made for heavy duty volume production, this Lee Precision Six Cavity Bullet Mold produces .358 diameter 158 grain Semi Wad Cutter nose bullets suitable for .38 Special, .38 S&W (Smith & Wesson), .38 Colt New Police, .357 Magnum and similar cartridges. This mold, like all Lee Precision molds, is made from aluminum and so is completely rust resistant, lighter, and heats up and cools down faster than other brands made from iron or steel. As a result, this Lee mold is easier to use, causes less operator fatigue during casting and can produce more consistent bullets than other molds made from iron or steel. Lee's 6 cavity mold blocks are machined from aluminum and assembled with steel bushings and alignment pins for lasting precision.

A sprue plate is included but Handles are sold separately. The bullet weight specified is based on using Lee's suggested alloy, your results may vary depending on the actual alloy used.



  • (2) aluminum Mold Block halves (mold handles NOT included)
  • Hard anodized Sprue Plate with handle


  • Produces bullets that fit 38 Special, 38 S&W, 38 Colt New Police, 357 Magnum and similar sized cartridges.
  • Bullet diameter: .358 inches
  • Bullet weight: 158 grains (with Lee's suggested alloy)
  • Bullet overall length: .665 inches
  • Distance from nose to first lube groove: .250 inches
  • Bullet shape: Semi Wad Cutter 
  • Ballistic Coefficient: .117
  • 6 bullets are produced with each casting.
  • Mold block halves are machined from aluminum.
  • Assembled with steel bushings and alignment pins for lasting precision.
  • Cam operated sprue plate to eliminate the pounding common to ordinary molds.
  • A tangential cutoff helps reduce the nip at cutoff.


Lead Information:

  • The following lead information is from the Lee Precision Modern Reloading 2nd Edition Book, Pages 119 & 120.
  • For best results, bullet strength must be matched to breech pressure.
  • Black Powder guns require Pure Lead.
  • Target handgun loads should use Lead with 1% Tin. Tin makes bullet alloy more castable & harder.
  • Lead with some wheel weights used for high pressure handguns.
  • Use Wheel Weights for very light rifle loads. 
  • High Pressure Rifle loads use Linotype.
  • Beware of Zinc! One part Zinc in 10,000 parts of Lead Alloy will ruin it's castability.

  WARNING:  Melting lead and casting lead objects will expose you and others in the area to lead which is known to cause birth defects, other reproductive harm and cancer. 

                            USE STRONG VENTILATION

Lead contamination in the air, dust and on your skin is invisible. Keep Children and pregnant women away during use and until clean-up is complete. Risk can be reduced, BUT NOT eliminated , with strong ventilation. Washing hands immediately after use of these products before eating or smoking. Careful cleaning of surfaces and floors with disposable wipes, after lead dust has settled. Use lead-specific cleaner with EDTA or high phosphate detergent (such as dishwasher detergent). Bag wipes for disposal.



  • DO NOT USE more powder than recommended
  • DO NOT USE a heavier bullet than recommended
  • DO NOT SEAT the bullet deeper than normal
  • DO NOT USE magnum primers unless using a slow burning ball powder
  • Greatly oversize bullets, excessively hard bullets or cases that are too long will cause higher pressures
  • High temperatures or cartridges that were stored in a hot car or trunk will produce higher pressures


Ammunition reloading can be dangerous if done improperly, and should not be attempted by persons not willing and able to read and follow the instructions included with each product exactly.

  • Always wear safety glasses when reloading and shooting.
  • Ammunition loaded with these tools should be used in modern guns, in good condition.
  • Children should not be permitted to reload ammunition without strict parental supervision.
  • Primers and gun powders, like gasoline and matches, can be dangerous if improperly handled or misused.
  • We do not accept responsibility for ammunition loaded with these tools, as we have no control over the manufacture and storage of components or the loading procedure and techniques used.



Help for product 90327

Write a review

Note: HTML is not translated!
    Bad           Good

Lee Precision Mold 6 Cavity C358-158-SWC

 Brand:  Lee Precision 
 Product Code:  90327 
 Reward Points:  37 
 Availability:  Out Of Stock 
 MSRP:  $54.00 
 MPN:  90327 
 Material:  Aluminum, Steel 
 Color:  Aluminum, Black 
 Condition:  new 
 Country of Origin:  United States 
 Package Quantity: 
 Product Weight:  1.2 lbs 
 UPC:  734307903275 
 Status:  New 
 Shipping Restrictions:  No 
 Carrier Restrictions:  No 
 DOT Regulated:  No 
 Calibers:  .38 Special, .38 S&W, .38 Colt New Police, .357 Magnum  
 Bullet Type:  SemiWad Cutter, Gas Check 
 Bullet Weight:  158 grain 
 Bullet Diameter:  .358 inches 

  • $36.79

  • Price in reward points: 2208

Help for product 90327
Parts Manual Video

Related Products

Lee Precision Mold Double Cavity TL358-158-SWC

Lee Precision Mold Double Cavity TL358-158-SWC

This Lee Precision Double Cavity Bullet Mold produces .358 diameter, 150 grain Semi Wad round nose&n..


Tags: lee, precision, mold, cavity, c358-158-swc, .38, special, s&w, colt, new, police, .357, mag s&w s&w

The product is currently Out-of-Stock. Enter your email address below and we will notify you as soon as the product is available.